How To Measure Cabinets For Countertops

Measure the length of all countertops (measure in inches) measure depth (width) of all countertops; Putting a level on the cabinets will give you an idea if the cabinets are leveled.

How to Measure the Correct Upper Height from

For galley kitchens or in island situations, don’t be concerned about scaling the aisle separations.

How to measure cabinets for countertops. Use a good quality steel tape measure; Measure depth, from wall or back of counter to front for each section as well. Indicate where the sink and other appliances land

•tape measure • pen • paper • calculator. 2.include the spaces for your sink, cooktop, bar sink, etc. 1.draw a diagram of your countertop space on the paper.

To measure your cabinets, you do basically the same thing you did for your countertop. Measure length from end of counter to wall or point where next section of countertop begins. Don’t stop measuring when you reach a sink but continue to measure until you reach the end of a cabinet, appliance, or a wall.

If the countertops fit well and no adjustments are needed proceed as follows; Multiple length by width and divide by 144. This is the square footage of your countertop.

Begin with a scale drawing of your countertop layout or layouts. First determine the depth of the cabinets under the countertop. When measuring just base cabinets without a top, add 1.5” to the width to accommodate for overhang.

Measure the length of one section of your countertops by running a measuring tape flush along the back edge of the section from one end to the other end. If you are installing a floating floor that goes in after the cabinets, you’ll need to raise them above the flooring so your appliances will fit under the countertops. If you have a window between your wall cabinets, measure the width of the window and the distance from the center of the window to the nearest corner of the room.

Use your tape measure to measure the countertop length from wall to wall (in inches), not just from one edge of your current countertop to the other. To see how much horizontal space your cabinets can take up, measure the width of each wall from corner to corner and record the numbers on your blueprint. Using a good quality steel tape measure, make sure the tip is 90° to the blade (not bent).

You just take the length x width of each section, and add it together. 4.measure the countertop length from wall to wall (in inches). How to measure for the proper fit if new cabinets are being installed, always measure after the base cabinets are set.

Take your measurements from 36 in (91 cm) up, or the height most cabinet countertops. How to measure for the proper fit if you are planning to replace your cabinets, always measure for the countertops after the base cabinets are set. If you are replacing only the countertops, simply measure the old countertops for size.

125” x 25” = 3125”. If the countertop only is being replaced, simply measure the old countertop (unless changing the configuration). Get results from 6 engines at once

For easy measuring, use a piece of flooring and underlayment as a guide to mark the height by setting them on the high spot. Measure the cabinets that will be. While you are measuring the countertops, you should always measure the wall where the countertop will sit up against for getting the most accurate measurements.

3.indicate where there are walls in the space (if possible). Measure the width of each wall. The depth of a cabinet is the distance measured between the front face of the cabinet and the wall behind it.

Take measurements along the wall of all the existing countertops. Again, make sure to record all measurements in inches. Write down the length in the appropriate space on your scale drawing or piece paper whichever case may be.

Same size as a in this case, so 1562.5”. Divide the figure you get by performing the steps above by 144. Standard width of a base cabinet is 24”.

Measure the width (w) and length (l) of each piece, and mark each measurement on the sketch. For lower countertops, you need to account for the overhang of the countertop, so just measure from the back of the cabinet to the front edge. Base cabinets are normally 36 inches high.

Make an outline sketch of what the countertops look like (fig.1). Make an outline sketch of what the countertops will look like (fig. Now that you have a drawing ready, it’s time to begin taking measurements.

Most all countertop base cabinets are manufactured in standard depths of 18, 24 or 30 inches. Use the tape measure to measure each section of countertop in inches. Get results from 6 engines at once

You include the cabinets in your sketch, and then measure the width of the cabinets, adding 1 to 1/2 inches. Measure the length and width of your countertop in inches. Measuring your existing kitchen or bathroom countertops.

On cabinets with face frames, check to see if the face frame overhangs the side of the cabinet (fig. In this article, we will go over step by step how to measure countertops accurately, and. 62.5” x 25” = 1562.5”.

If the cabinets are not leveled when they are installed, the best thing to do is to correct the cabinets first, then take measurements. Follow these steps to measure for countertops. To maximize efficiency, the sum of the three distances should be no more than 26 feet.

Make sure the tip is 90° to the blade (not bent).

Size Charts Cumberland Collection Builders